You can build a PC with just a screwdriver or two on hand, but you’ll have an easier time of it if you have all the essentials on hand. That includes tools to get you out of sticky spots, which always occur when you assume they won’t. Keep these 10 items on hand for builds and they’ll keep your assembly woes to a minimum.
We’ve divided the list into the absolute essentials (for the minimalists out there) as well as our recommended additions for a well-rounded kit. But really, there’s no need to scrimp. All of these tools are very affordable.
Since M.2 SSD mounting screws are delicate, you won’t need much torque to get them in or out and thus a slender or small screwdriver works fine. You should get a magnetized one though, as screws that take a Phillips #1 tend to be small and easy to lose track of.
Builds that don’t use any M.2 SSDs can get away with just a Phillips #2, but we’ve found that it never hurts to have a Phillips #1 on hand.
You should put screws in some kind of container as you work—a shallow dish or bowl, a tray, even a cup. (Using more than one is even better, as you can keep track of different screw types more easily.) Placing everything loose onto a table usually results in missing screws, while clothing pockets run the risk of screws becoming lost as you move around.
If not tightened down sufficiently, motherboard standoffs can come loose as you try to loosen the screws holding the mainboard in place. The screw remains tight within the standoff, however—leaving you in purgatory until you can keep the standoff still as you remove the screw. In fact, further down this list are tools to help fix that common problem.
But if you own a hex nut driver in the right size, you can avoid that time and irritation. Before you mount the motherboard, slip it over the standoffs and ensure each one is firmly attached to the case. No need to overtighten, either; just a bit past when the standoff first hits the metal of the case. Too much and you risk stripping the screw threads on the standoffs.
Think a spinning standoff will never happen to you? Readjustments can come up during building. Also, later maintenance on your system may require it. Believe us, nothing stokes deep rage like when a standoff gets stuck as you try to remove a mobo for an RMA return.
Some cases come with an accessory—a small metal piece compatible with a Phillips #2 screwdriver—that fulfills this same role, but not all do. You may also have a bit like this in a screwdriver kit you already own or will be buying (look for the M5 size).
Normal lighting can create shadows that reduce what you can see while working in a case, especially if it’s a dark chassis. A good flashlight makes clear where stray screws rolled, the labels on front panel pins, and where that one last screw hole on the mobo is. You can get an affordable tactical flashlightRemove non-product link starting at about $15.
For the ultimate in practicality, a headlamp makes working in dark, tight spots of your case even easier—since it’s strapped to your forehead, you can keep working without interruption. You can get a reliable one for just a bit more than a flashlight, with this popular modelRemove non-product link coming in at $20.
Additional recommended tools for PC building
Every now and then, the screw holding your motherboard in place won’t come loose. Instead, the standoff underneath the mobo does, resulting in the screw and standoff spinning around as an unremovable unit. This is a more common occurance during repairs or upgrades, but it can also happen during a build when undoing a screwup.
To fix this, you need to keep the standoff from moving while you loosen the screw—a job neatly filled by a small adjustable wrenchRemove non-product link (also known colloquially as a crescent wrench), which can be bought for under $15. Slide it between the motherboard and the case, then clamp it down on the standoff. Then hold that pesky standoff in place to take out the screw.
An adjustable wrench can also be used to tighten standoffs before you install a motherboard, if you don’t have a hex nut driver on hand.
An adjustable wrench is ideal since it leaves no marks on a standoff after extraction, but every situation with a spinning standoff leaves a different amount of room to work in. If you can’t maneuver one into position, try the next item on this list: a hemostat.
When you’re faced with a hard-to-reach standoff trapped under a motherboard, a hemostatRemove non-product link can help you out of that jam. These locking forceps are slender and needle-nosed—ideal for getting under the motherboard when there’s limited room. You can sometimes even clamp onto the standoff’s screw threads poking out the back of the motherboard tray. Adding one to your lineup won’t cost much, either, as it’ll run about $5.
MABIS Kelly Forceps, Medical Forceps, Locking Forceps, Silver, 5.5″
Using a hemostat is straightforward: Get the jaws around the standoff, then squeeze the handles to lock it. (Note: Most hemostats have teeth that can scratch up your standoff’s finish. To avoid this outcome, wedge part of a rubber band between it and the standoff whenever possible.)
As a reminder, you’ll barely ever need this tool if you make sure your case’s standoff screws are firmly seated before installing a motherboard. Use a hex nut driver or an adjustable wrench to tighten them just a bit past when the standoff first bottoms out. (Don’t go too crazy—overtightening can create its own problems, i.e., stripped screw threads.)
A hemostat also comes in handy if you opt for rubber “screws” for mounting case fans. Just clamp onto one end to maintain your grip while tugging it through the fan.
You can’t always predict when a case sports a front panel held in place by stubborn plastic clips—much less ones located in hard-to-reach places. A flathead screwdriver can help you push them in to release. A standard driver with a longer neckRemove non-product link is ideal, since it will fit into tight spots more easily. For size, a 1/4- or 3/8-inch head and an 8-inch neck should work.
Note that these can dent and scratch the plastic if you apply them directly. You can put a bit of protective material (a bit of rubber band or a cotton ball) between the screwdriver head and the plastic before levering away.
Small rubber bandsRemove non-product link can protect paint from the rough teeth on pliers and hemostats, serve as a poor person’s substite for Velcro ties, and add extra grip in tight situations (like if you need more traction on a slightly stripped screw head). In a pinch, a couple of these can make it easier to slide side panels off of cases too, if you have slippery hands. (Upgrade version for dealing with side panels: a rubber jar openerRemove non-product link, which is easier for big hands to hold in place.)
Stripped a screw head? You can extract the screw from your build by using a vise grip if a hemostat doesn’t generate enough torque. Clamp the jaws of these locking pliers around the screw head, then start turning. (Be mindful of what else is in the vicinity, as these are a bit bulky.) You can usually pick up a 6-inch vise gripRemove non-product link for under $15.
Also like a hemostat, you can use a vise grip to help with the use of rubber “screws” for mounting case fans. Lock onto one end to maintain your grip while yanking it through the fan.
Note: When you purchase something after clicking links in our articles, we may earn a small commission. Read ouraffiliate link policyfor more details.
Alaina Yee is PCWorld's resident bargain hunter—when she's not covering PC building, computer components, mini-PCs, and more, she's scouring for the best tech deals. Previously her work has appeared in PC Gamer, IGN, Maximum PC, and Official Xbox Magazine. You can find her on Twitter at @morphingball.
eBay CouponHalloween 2021 eBay coupon: Get extra 15% off orders $25+
Hp Coupon CodeExtra 15% off HP coupon for ready to ship business laptops & workstations